WireSizing
Wire gauge reference & calculator

1-1/4" ENT Conduit Fill Chart

14 AWG THHN
60
conductors max
12 AWG THHN
43
conductors max
10 AWG THHN
27
conductors max
Usable area at 40% fill: 0.581 in² · NEC Chapter 9, Tables 1, 4 and 5

About ENT (Electrical Nonmetallic Tubing)

Corrugated pliable plastic tubing (“smurf tube”), bent by hand and used inside walls, above suspended ceilings and encased in concrete slabs. Current tables give it the same internal dimensions as Schedule 40 PVC. Trade size 1-1/4" is covered by NEC Article 362, and its internal dimensions come from NEC Chapter 9, Table 4.

1-1/4" ENT — Internal Area & Fill Limits

Trade size1-1/4"
Total internal area (100%)1.453 in²
1 conductor (53%)0.77 in²
2 conductors (31%)0.45 in²
Over 2 conductors (40%)0.581 in²

1-1/4" ENT — Max THHN / THWN-2 Conductors

Wire size Area (in²) Max conductors
140.009760
120.013343
100.021127
80.036616
60.050711
40.08247
30.09736
20.11585
10.15623
1/00.18553
2/00.22232
3/00.26791
4/00.32371
250 kcmil0.39701
300 kcmil0.46081
350 kcmil0.52421
400 kcmil0.58631
500 kcmil0.70731
600 kcmil0.8676—
700 kcmil0.9887—
750 kcmil1.0496—
800 kcmil1.1085—
900 kcmil1.2311—
1000 kcmil1.3478—
Conductor areas from NEC Chapter 9, Table 5 (THHN, THWN, THWN-2). Counts assume all conductors are the same size and insulation type.

1-1/4" ENT — Max XHHW / XHHW-2 Conductors

Wire size Area (in²) Max conductors
140.013942
120.018132
100.024324
80.043713
60.059010
40.08147
30.09626
20.11465
10.15343
1/00.18253
2/00.21902
3/00.26421
4/00.31971
250 kcmil0.39041
300 kcmil0.45361
350 kcmil0.51661
400 kcmil0.57821
500 kcmil0.69841
600 kcmil0.8709—
700 kcmil0.9923—
750 kcmil1.0532—
800 kcmil1.1122—
900 kcmil1.2351—
1000 kcmil1.3519—
XHHW and XHHW-2 have no nylon jacket, so below 4 AWG they are physically larger than THHN and fewer fit. Areas from NEC Chapter 9, Table 5.

How the 40% conduit fill rule works

Conduit fill is a pure area calculation. Take the internal area of the raceway from NEC Chapter 9, Table 4, multiply by the allowable percentage from Table 1, then divide by the area of one conductor from Table 5. Round down, except that NEC Chapter 9, Note 7 lets you round up to the next whole number when the result has a decimal of 0.8 or more and all conductors are the same size.

Max conductors = conduit area × fill % ÷ conductor area (Note 7 rounding)

For 1-1/4" ENT with 12 AWG THHN: 1.453 × 0.40 ÷ 0.0133 = 43.70 → 43 conductors

Nipples are the exception: a conduit or tubing length not exceeding 24 inches between boxes or enclosures may be filled to 60% per NEC Chapter 9, Table 1, Note 4. For 1-1/4" ENT that raises the usable area from 0.581 in² to 0.872 in².

Other ENT Sizes

1-1/4" in Other Conduit Types

Frequently Asked Questions

How many wires fit in 1-1/4-inch ENT conduit?

A 1-1/4-inch ENT conduit has 1.453 square inches of internal area. With more than two conductors the NEC limits fill to 40%, or 0.581 in². That works out to 43 #12 THHN, 60 #14 THHN, 27 #10 THHN, or 16 #8 THHN conductors.

How many 12 AWG THHN wires fit in 1-1/4-inch ENT?

43 conductors. Each 12 AWG THHN wire is 0.0133 in² per NEC Chapter 9, Table 5, and the 40% fill area of 1-1/4-inch ENT is 0.581 in².

What is the maximum fill percentage for conduit?

NEC Chapter 9, Table 1 sets three limits: 53% for a single conductor, 31% for exactly two conductors, and 40% for three or more. The lower two-conductor figure exists because two round conductors pack poorly inside a round raceway.

Related

Conduit fill calculator → All conduit fill charts → Ampacity tables →