How many wires fit in 1-1/4-inch Rigid (RMC) conduit?

A 1-1/4-inch Rigid (RMC) conduit has 1.526 square inches of internal area. With more than two conductors the NEC limits fill to 40%, or 0.610 in². That works out to 45 #12 THHN, 62 #14 THHN, 28 #10 THHN, or 16 #8 THHN conductors.

How many 12 AWG THHN wires fit in 1-1/4-inch Rigid (RMC)?

45 conductors. Each 12 AWG THHN wire is 0.0133 in² per NEC Chapter 9, Table 5, and the 40% fill area of 1-1/4-inch Rigid (RMC) is 0.610 in².

What is the maximum fill percentage for conduit?

NEC Chapter 9, Table 1 sets three limits: 53% for a single conductor, 31% for exactly two conductors, and 40% for three or more. The lower two-conductor figure exists because two round conductors pack poorly inside a round raceway.

Does the equipment grounding conductor count toward conduit fill?

Yes. Every conductor in the raceway counts toward the cross-sectional fill calculation, including equipment grounding conductors and neutrals. Grounding conductors do not count as current-carrying conductors for the separate NEC 310.15(C)(1) derating calculation, but they still occupy space.

1-1/4" Rigid (RMC) Conduit Fill Chart

14 AWG THHN

conductors max

12 AWG THHN

conductors max

10 AWG THHN

conductors max

Usable area at 40% fill: 0.610 in² · NEC Chapter 9, Tables 1, 4 and 5

About Rigid Metal Conduit (RMC)

Heavy-wall threaded steel conduit — the thickest and strongest raceway in the NEC. Used for service masts, hazardous locations, and anywhere physical damage is likely. Trade size 1-1/4" is covered by NEC Article 344, and its internal dimensions come from NEC Chapter 9, Table 4.

1-1/4" Rigid (RMC) — Internal Area & Fill Limits

Trade size	1-1/4"
Total internal area (100%)	1.526 in²
1 conductor (53%)	0.809 in²
2 conductors (31%)	0.473 in²
Over 2 conductors (40%)	0.610 in²

1-1/4" Rigid (RMC) — Max THHN / THWN-2 Conductors

Wire size	Area (in²)	Max conductors
14	0.0097	62
12	0.0133	45
10	0.0211	28
8	0.0366	16
6	0.0507	12
4	0.0824	7
3	0.0973	6
2	0.1158	5
1	0.1562	3
1/0	0.1855	3
2/0	0.2223	2
3/0	0.2679	1
4/0	0.3237	1
250 kcmil	0.3970	1
300 kcmil	0.4608	1
350 kcmil	0.5242	1
400 kcmil	0.5863	1
500 kcmil	0.7073	1

Conductor areas from NEC Chapter 9, Table 5 (THHN, THWN, THWN-2). Counts assume all conductors are the same size and insulation type, which is the condition NEC Annex C tables are built on. Mix sizes or insulations and you must add the individual areas by hand against the fill area above.

1-1/4" Rigid (RMC) — Max XHHW / XHHW-2 Conductors

Wire size	Area (in²)	Max conductors
14	0.0139	43
12	0.0181	33
10	0.0243	25
8	0.0437	13
6	0.0590	10
4	0.0814	7
3	0.0962	6
2	0.1146	5
1	0.1534	3
1/0	0.1825	3
2/0	0.2190	2
3/0	0.2642	1
4/0	0.3197	1
250 kcmil	0.3904	1
350 kcmil	0.5153	1
500 kcmil	0.6984	1

XHHW and XHHW-2 have no nylon jacket, so below 4 AWG they are physically larger than THHN and fewer fit. From 4 AWG up they are slightly smaller. Areas from NEC Chapter 9, Table 5.

How the 40% conduit fill rule works

Conduit fill is a pure area calculation. Take the internal area of the raceway from NEC Chapter 9, Table 4, multiply by the allowable percentage from Table 1, then divide by the area of one conductor from Table 5. Round down — you cannot install a fraction of a wire.

Max conductors = floor( conduit area × fill % ÷ conductor area )

For 1-1/4" Rigid (RMC) with 12 AWG THHN: floor( 1.526 × 0.40 ÷ 0.0133 ) = 45 conductors

The three percentages in NEC Chapter 9, Table 1 are not arbitrary. A single conductor gets 53% because it can be pulled straight down the middle. Exactly two conductors get only 31% because two circles inside a circle waste the most space. Three or more conductors nest efficiently again, so the limit rises to 40%.

Fill is only half the job. Once you have more than three current-carrying conductors in the same raceway, NEC 310.15(C)(1) also derates their ampacity — 80% for 4–6 conductors, 70% for 7–9, 50% for 10–20. A conduit can be legally filled and still leave your conductors undersized for the load. See NEC Table 310.15 for the full derating factors.

Nipples are the exception: a conduit or tubing length not exceeding 24 inches between boxes or enclosures may be filled to 60% per NEC Chapter 9, Table 1, Note 4 — and no ampacity derating applies to it. For 1-1/4" Rigid (RMC) that raises the usable area from 0.610 in² to 0.916 in².