How many wires fit in 4-inch IMC conduit?

A 4-inch IMC conduit has 13.631 square inches of internal area. With more than two conductors the NEC limits fill to 40%, or 5.452 in². That works out to 409 #12 THHN, 562 #14 THHN, 258 #10 THHN, or 148 #8 THHN conductors.

How many 12 AWG THHN wires fit in 4-inch IMC?

409 conductors. Each 12 AWG THHN wire is 0.0133 in² per NEC Chapter 9, Table 5, and the 40% fill area of 4-inch IMC is 5.452 in².

What is the maximum fill percentage for conduit?

NEC Chapter 9, Table 1 sets three limits: 53% for a single conductor, 31% for exactly two conductors, and 40% for three or more. The lower two-conductor figure exists because two round conductors pack poorly inside a round raceway.

Does the equipment grounding conductor count toward conduit fill?

Yes. Every conductor in the raceway counts toward the cross-sectional fill calculation, including equipment grounding conductors and neutrals. Grounding conductors do not count as current-carrying conductors for the separate NEC 310.15(C)(1) derating calculation, but they still occupy space.

4" IMC Conduit Fill Chart

14 AWG THHN

562

conductors max

12 AWG THHN

409

conductors max

10 AWG THHN

258

conductors max

Usable area at 40% fill: 5.452 in² · NEC Chapter 9, Tables 1, 4 and 5

About Intermediate Metal Conduit (IMC)

Threaded steel conduit with a thinner wall than RMC, so it is lighter and has slightly more internal area. Permitted anywhere RMC is permitted. Trade size 4" is covered by NEC Article 342, and its internal dimensions come from NEC Chapter 9, Table 4.

4" IMC — Internal Area & Fill Limits

Trade size	4"
Total internal area (100%)	13.631 in²
1 conductor (53%)	7.224 in²
2 conductors (31%)	4.226 in²
Over 2 conductors (40%)	5.452 in²

4" IMC — Max THHN / THWN-2 Conductors

Wire size	Area (in²)	Max conductors
14	0.0097	562
12	0.0133	409
10	0.0211	258
8	0.0366	148
6	0.0507	107
4	0.0824	66
3	0.0973	56
2	0.1158	47
1	0.1562	34
1/0	0.1855	29
2/0	0.2223	24
3/0	0.2679	20
4/0	0.3237	16
250 kcmil	0.3970	13
300 kcmil	0.4608	11
350 kcmil	0.5242	10
400 kcmil	0.5863	9
500 kcmil	0.7073	7

Conductor areas from NEC Chapter 9, Table 5 (THHN, THWN, THWN-2). Counts assume all conductors are the same size and insulation type, which is the condition NEC Annex C tables are built on. Mix sizes or insulations and you must add the individual areas by hand against the fill area above.

4" IMC — Max XHHW / XHHW-2 Conductors

Wire size	Area (in²)	Max conductors
14	0.0139	392
12	0.0181	301
10	0.0243	224
8	0.0437	124
6	0.0590	92
4	0.0814	66
3	0.0962	56
2	0.1146	47
1	0.1534	35
1/0	0.1825	29
2/0	0.2190	24
3/0	0.2642	20
4/0	0.3197	17
250 kcmil	0.3904	13
350 kcmil	0.5153	10
500 kcmil	0.6984	7

XHHW and XHHW-2 have no nylon jacket, so below 4 AWG they are physically larger than THHN and fewer fit. From 4 AWG up they are slightly smaller. Areas from NEC Chapter 9, Table 5.

How the 40% conduit fill rule works

Conduit fill is a pure area calculation. Take the internal area of the raceway from NEC Chapter 9, Table 4, multiply by the allowable percentage from Table 1, then divide by the area of one conductor from Table 5. Round down — you cannot install a fraction of a wire.

Max conductors = floor( conduit area × fill % ÷ conductor area )

For 4" IMC with 12 AWG THHN: floor( 13.631 × 0.40 ÷ 0.0133 ) = 409 conductors

The three percentages in NEC Chapter 9, Table 1 are not arbitrary. A single conductor gets 53% because it can be pulled straight down the middle. Exactly two conductors get only 31% because two circles inside a circle waste the most space. Three or more conductors nest efficiently again, so the limit rises to 40%.

Fill is only half the job. Once you have more than three current-carrying conductors in the same raceway, NEC 310.15(C)(1) also derates their ampacity — 80% for 4–6 conductors, 70% for 7–9, 50% for 10–20. A conduit can be legally filled and still leave your conductors undersized for the load. See NEC Table 310.15 for the full derating factors.

Nipples are the exception: a conduit or tubing length not exceeding 24 inches between boxes or enclosures may be filled to 60% per NEC Chapter 9, Table 1, Note 4 — and no ampacity derating applies to it. For 4" IMC that raises the usable area from 5.452 in² to 8.179 in².