WireSizing
Wire gauge reference & calculator

1-1/2" Flexible Metal (FMC) Conduit Fill Chart

14 AWG THHN
76
conductors max
12 AWG THHN
56
conductors max
10 AWG THHN
35
conductors max
Usable area at 40% fill: 0.743 in² · NEC Chapter 9, Tables 1, 4 and 5

About Flexible Metal (FMC) (Flexible Metal Conduit (FMC))

Spiral-wound interlocked steel or aluminum “Greenfield”. Used for short whips to motors, fixtures and equipment that vibrates or needs to move. Trade size 1-1/2" is covered by NEC Article 348, and its internal dimensions come from NEC Chapter 9, Table 4.

1-1/2" Flexible Metal (FMC) — Internal Area & Fill Limits

Trade size1-1/2"
Total internal area (100%)1.858 in²
1 conductor (53%)0.985 in²
2 conductors (31%)0.576 in²
Over 2 conductors (40%)0.743 in²

1-1/2" Flexible Metal (FMC) — Max THHN / THWN-2 Conductors

Wire size Area (in²) Max conductors
140.009776
120.013356
100.021135
80.036620
60.050714
40.08249
30.09737
20.11586
10.15624
1/00.18554
2/00.22233
3/00.26792
4/00.32371
250 kcmil0.39701
300 kcmil0.46081
350 kcmil0.52421
400 kcmil0.58631
500 kcmil0.70731
600 kcmil0.86761
700 kcmil0.9887—
750 kcmil1.0496—
800 kcmil1.1085—
900 kcmil1.2311—
1000 kcmil1.3478—
Conductor areas from NEC Chapter 9, Table 5 (THHN, THWN, THWN-2). Counts assume all conductors are the same size and insulation type.

1-1/2" Flexible Metal (FMC) — Max XHHW / XHHW-2 Conductors

Wire size Area (in²) Max conductors
140.013953
120.018141
100.024330
80.043717
60.059012
40.08149
30.09627
20.11466
10.15345
1/00.18254
2/00.21903
3/00.26423
4/00.31971
250 kcmil0.39041
300 kcmil0.45361
350 kcmil0.51661
400 kcmil0.57821
500 kcmil0.69841
600 kcmil0.87091
700 kcmil0.9923—
750 kcmil1.0532—
800 kcmil1.1122—
900 kcmil1.2351—
1000 kcmil1.3519—
XHHW and XHHW-2 have no nylon jacket, so below 4 AWG they are physically larger than THHN and fewer fit. Areas from NEC Chapter 9, Table 5.

How the 40% conduit fill rule works

Conduit fill is a pure area calculation. Take the internal area of the raceway from NEC Chapter 9, Table 4, multiply by the allowable percentage from Table 1, then divide by the area of one conductor from Table 5. Round down, except that NEC Chapter 9, Note 7 lets you round up to the next whole number when the result has a decimal of 0.8 or more and all conductors are the same size.

Max conductors = conduit area × fill % ÷ conductor area (Note 7 rounding)

For 1-1/2" Flexible Metal (FMC) with 12 AWG THHN: 1.858 × 0.40 ÷ 0.0133 = 55.88 → 56 conductors

Nipples are the exception: a conduit or tubing length not exceeding 24 inches between boxes or enclosures may be filled to 60% per NEC Chapter 9, Table 1, Note 4. For 1-1/2" Flexible Metal (FMC) that raises the usable area from 0.743 in² to 1.115 in².

Other Flexible Metal (FMC) Sizes

1-1/2" in Other Conduit Types

Frequently Asked Questions

How many wires fit in 1-1/2-inch Flexible Metal Conduit conduit?

A 1-1/2-inch Flexible Metal Conduit conduit has 1.858 square inches of internal area. With more than two conductors the NEC limits fill to 40%, or 0.743 in². That works out to 56 #12 THHN, 76 #14 THHN, 35 #10 THHN, or 20 #8 THHN conductors.

How many 12 AWG THHN wires fit in 1-1/2-inch Flexible Metal Conduit?

56 conductors. Each 12 AWG THHN wire is 0.0133 in² per NEC Chapter 9, Table 5, and the 40% fill area of 1-1/2-inch Flexible Metal Conduit is 0.743 in².

What is the maximum fill percentage for conduit?

NEC Chapter 9, Table 1 sets three limits: 53% for a single conductor, 31% for exactly two conductors, and 40% for three or more. The lower two-conductor figure exists because two round conductors pack poorly inside a round raceway.

Related

Conduit fill calculator → All conduit fill charts → Ampacity tables →