WireSizing
Wire gauge reference & calculator

1-1/2" Liquidtight (LFMC) Conduit Fill Chart

14 AWG THHN
81
conductors max
12 AWG THHN
59
conductors max
10 AWG THHN
37
conductors max
Usable area at 40% fill: 0.792 in² · NEC Chapter 9, Tables 1, 4 and 5

About Liquidtight (LFMC) (Liquidtight Flexible Metal Conduit (LFMC))

Flexible metal conduit with a sunlight- and oil-resistant thermoplastic jacket. The usual choice for outdoor equipment whips: air conditioners, pumps, rooftop units. Trade size 1-1/2" is covered by NEC Article 350, and its internal dimensions come from NEC Chapter 9, Table 4.

1-1/2" Liquidtight (LFMC) — Internal Area & Fill Limits

Trade size1-1/2"
Total internal area (100%)1.981 in²
1 conductor (53%)1.05 in²
2 conductors (31%)0.614 in²
Over 2 conductors (40%)0.792 in²

1-1/2" Liquidtight (LFMC) — Max THHN / THWN-2 Conductors

Wire size Area (in²) Max conductors
140.009781
120.013359
100.021137
80.036621
60.050715
40.08249
30.09738
20.11587
10.15625
1/00.18554
2/00.22233
3/00.26793
4/00.32371
250 kcmil0.39701
300 kcmil0.46081
350 kcmil0.52421
400 kcmil0.58631
500 kcmil0.70731
600 kcmil0.86761
700 kcmil0.98871
750 kcmil1.04961
800 kcmil1.1085—
900 kcmil1.2311—
1000 kcmil1.3478—
Conductor areas from NEC Chapter 9, Table 5 (THHN, THWN, THWN-2). Counts assume all conductors are the same size and insulation type.

1-1/2" Liquidtight (LFMC) — Max XHHW / XHHW-2 Conductors

Wire size Area (in²) Max conductors
140.013957
120.018143
100.024332
80.043718
60.059013
40.08149
30.09628
20.11467
10.15345
1/00.18254
2/00.21903
3/00.26423
4/00.31971
250 kcmil0.39041
300 kcmil0.45361
350 kcmil0.51661
400 kcmil0.57821
500 kcmil0.69841
600 kcmil0.87091
700 kcmil0.99231
750 kcmil1.0532—
800 kcmil1.1122—
900 kcmil1.2351—
1000 kcmil1.3519—
XHHW and XHHW-2 have no nylon jacket, so below 4 AWG they are physically larger than THHN and fewer fit. Areas from NEC Chapter 9, Table 5.

How the 40% conduit fill rule works

Conduit fill is a pure area calculation. Take the internal area of the raceway from NEC Chapter 9, Table 4, multiply by the allowable percentage from Table 1, then divide by the area of one conductor from Table 5. Round down, except that NEC Chapter 9, Note 7 lets you round up to the next whole number when the result has a decimal of 0.8 or more and all conductors are the same size.

Max conductors = conduit area × fill % ÷ conductor area (Note 7 rounding)

For 1-1/2" Liquidtight (LFMC) with 12 AWG THHN: 1.981 × 0.40 ÷ 0.0133 = 59.58 → 59 conductors

Nipples are the exception: a conduit or tubing length not exceeding 24 inches between boxes or enclosures may be filled to 60% per NEC Chapter 9, Table 1, Note 4. For 1-1/2" Liquidtight (LFMC) that raises the usable area from 0.792 in² to 1.189 in².

Other Liquidtight (LFMC) Sizes

1-1/2" in Other Conduit Types

Frequently Asked Questions

How many wires fit in 1-1/2-inch Liquidtight Flexible Metal Conduit conduit?

A 1-1/2-inch Liquidtight Flexible Metal Conduit conduit has 1.981 square inches of internal area. With more than two conductors the NEC limits fill to 40%, or 0.792 in². That works out to 59 #12 THHN, 81 #14 THHN, 37 #10 THHN, or 21 #8 THHN conductors.

How many 12 AWG THHN wires fit in 1-1/2-inch Liquidtight Flexible Metal Conduit?

59 conductors. Each 12 AWG THHN wire is 0.0133 in² per NEC Chapter 9, Table 5, and the 40% fill area of 1-1/2-inch Liquidtight Flexible Metal Conduit is 0.792 in².

What is the maximum fill percentage for conduit?

NEC Chapter 9, Table 1 sets three limits: 53% for a single conductor, 31% for exactly two conductors, and 40% for three or more. The lower two-conductor figure exists because two round conductors pack poorly inside a round raceway.

Related

Conduit fill calculator → All conduit fill charts → Ampacity tables →