How many wires fit in 1-1/2-inch PVC Sch 40 conduit?

A 1-1/2-inch PVC Sch 40 conduit has 1.986 square inches of internal area. With more than two conductors the NEC limits fill to 40%, or 0.794 in². That works out to 59 #12 THHN, 81 #14 THHN, 37 #10 THHN, or 21 #8 THHN conductors.

How many 12 AWG THHN wires fit in 1-1/2-inch PVC Sch 40?

59 conductors. Each 12 AWG THHN wire is 0.0133 in² per NEC Chapter 9, Table 5, and the 40% fill area of 1-1/2-inch PVC Sch 40 is 0.794 in².

What is the maximum fill percentage for conduit?

NEC Chapter 9, Table 1 sets three limits: 53% for a single conductor, 31% for exactly two conductors, and 40% for three or more. The lower two-conductor figure exists because two round conductors pack poorly inside a round raceway.

Does the equipment grounding conductor count toward conduit fill?

Yes. Every conductor in the raceway counts toward the cross-sectional fill calculation, including equipment grounding conductors and neutrals. Grounding conductors do not count as current-carrying conductors for the separate NEC 310.15(C)(1) derating calculation, but they still occupy space.

1-1/2" PVC Sch 40 Conduit Fill Chart

14 AWG THHN

conductors max

12 AWG THHN

conductors max

10 AWG THHN

conductors max

Usable area at 40% fill: 0.794 in² · NEC Chapter 9, Tables 1, 4 and 5

About PVC Conduit, Schedule 40

Rigid nonmetallic conduit, solvent-welded. The default for underground runs, wet locations, and corrosive environments. Schedule 80 has thicker walls and therefore less usable fill area. Trade size 1-1/2" is covered by NEC Article 352, and its internal dimensions come from NEC Chapter 9, Table 4.

1-1/2" PVC Sch 40 — Internal Area & Fill Limits

Trade size	1-1/2"
Total internal area (100%)	1.986 in²
1 conductor (53%)	1.052 in²
2 conductors (31%)	0.616 in²
Over 2 conductors (40%)	0.794 in²

1-1/2" PVC Sch 40 — Max THHN / THWN-2 Conductors

Wire size	Area (in²)	Max conductors
14	0.0097	81
12	0.0133	59
10	0.0211	37
8	0.0366	21
6	0.0507	15
4	0.0824	9
3	0.0973	8
2	0.1158	6
1	0.1562	5
1/0	0.1855	4
2/0	0.2223	3
3/0	0.2679	2
4/0	0.3237	1
250 kcmil	0.3970	1
300 kcmil	0.4608	1
350 kcmil	0.5242	1
400 kcmil	0.5863	1
500 kcmil	0.7073	1

Conductor areas from NEC Chapter 9, Table 5 (THHN, THWN, THWN-2). Counts assume all conductors are the same size and insulation type, which is the condition NEC Annex C tables are built on. Mix sizes or insulations and you must add the individual areas by hand against the fill area above.

1-1/2" PVC Sch 40 — Max XHHW / XHHW-2 Conductors

Wire size	Area (in²)	Max conductors
14	0.0139	57
12	0.0181	43
10	0.0243	32
8	0.0437	18
6	0.0590	13
4	0.0814	9
3	0.0962	8
2	0.1146	6
1	0.1534	5
1/0	0.1825	4
2/0	0.2190	3
3/0	0.2642	3
4/0	0.3197	1
250 kcmil	0.3904	1
350 kcmil	0.5153	1
500 kcmil	0.6984	1

XHHW and XHHW-2 have no nylon jacket, so below 4 AWG they are physically larger than THHN and fewer fit. From 4 AWG up they are slightly smaller. Areas from NEC Chapter 9, Table 5.

How the 40% conduit fill rule works

Conduit fill is a pure area calculation. Take the internal area of the raceway from NEC Chapter 9, Table 4, multiply by the allowable percentage from Table 1, then divide by the area of one conductor from Table 5. Round down — you cannot install a fraction of a wire.

Max conductors = floor( conduit area × fill % ÷ conductor area )

For 1-1/2" PVC Sch 40 with 12 AWG THHN: floor( 1.986 × 0.40 ÷ 0.0133 ) = 59 conductors

The three percentages in NEC Chapter 9, Table 1 are not arbitrary. A single conductor gets 53% because it can be pulled straight down the middle. Exactly two conductors get only 31% because two circles inside a circle waste the most space. Three or more conductors nest efficiently again, so the limit rises to 40%.

Fill is only half the job. Once you have more than three current-carrying conductors in the same raceway, NEC 310.15(C)(1) also derates their ampacity — 80% for 4–6 conductors, 70% for 7–9, 50% for 10–20. A conduit can be legally filled and still leave your conductors undersized for the load. See NEC Table 310.15 for the full derating factors.

Nipples are the exception: a conduit or tubing length not exceeding 24 inches between boxes or enclosures may be filled to 60% per NEC Chapter 9, Table 1, Note 4 — and no ampacity derating applies to it. For 1-1/2" PVC Sch 40 that raises the usable area from 0.794 in² to 1.192 in².