WireSizing
Wire gauge reference & calculator

3" PVC Schedule 80 Conduit Fill Chart

14 AWG THHN
265
conductors max
12 AWG THHN
193
conductors max
10 AWG THHN
122
conductors max
Usable area at 40% fill: 2.577 in² · NEC Chapter 9, Tables 1, 4 and 5

About PVC Schedule 80 (Rigid PVC Conduit, Schedule 80)

Heavy-wall PVC required where conduit is exposed to physical damage, such as risers on poles and service masts. Same outside diameter as Schedule 40, so the thicker wall takes noticeably more room from the inside. Trade size 3" is covered by NEC Article 352, and its internal dimensions come from NEC Chapter 9, Table 4.

3" PVC Schedule 80 — Internal Area & Fill Limits

Trade size3"
Total internal area (100%)6.442 in²
1 conductor (53%)3.414 in²
2 conductors (31%)1.997 in²
Over 2 conductors (40%)2.577 in²

3" PVC Schedule 80 — Max THHN / THWN-2 Conductors

Wire size Area (in²) Max conductors
140.0097265
120.0133193
100.0211122
80.036670
60.050751
40.082431
30.097326
20.115822
10.156216
1/00.185514
2/00.222311
3/00.26799
4/00.32378
250 kcmil0.39706
300 kcmil0.46085
350 kcmil0.52425
400 kcmil0.58634
500 kcmil0.70733
600 kcmil0.86763
700 kcmil0.98872
750 kcmil1.04961
800 kcmil1.10851
900 kcmil1.23111
1000 kcmil1.34781
Conductor areas from NEC Chapter 9, Table 5 (THHN, THWN, THWN-2). Counts assume all conductors are the same size and insulation type.

3" PVC Schedule 80 — Max XHHW / XHHW-2 Conductors

Wire size Area (in²) Max conductors
140.0139185
120.0181142
100.0243106
80.043759
60.059043
40.081431
30.096226
20.114622
10.153416
1/00.182514
2/00.219011
3/00.26429
4/00.31978
250 kcmil0.39046
300 kcmil0.45365
350 kcmil0.51665
400 kcmil0.57824
500 kcmil0.69843
600 kcmil0.87093
700 kcmil0.99232
750 kcmil1.05321
800 kcmil1.11221
900 kcmil1.23511
1000 kcmil1.35191
XHHW and XHHW-2 have no nylon jacket, so below 4 AWG they are physically larger than THHN and fewer fit. Areas from NEC Chapter 9, Table 5.

How the 40% conduit fill rule works

Conduit fill is a pure area calculation. Take the internal area of the raceway from NEC Chapter 9, Table 4, multiply by the allowable percentage from Table 1, then divide by the area of one conductor from Table 5. Round down, except that NEC Chapter 9, Note 7 lets you round up to the next whole number when the result has a decimal of 0.8 or more and all conductors are the same size.

Max conductors = conduit area × fill % ÷ conductor area (Note 7 rounding)

For 3" PVC Schedule 80 with 12 AWG THHN: 6.442 × 0.40 ÷ 0.0133 = 193.74 → 193 conductors

Nipples are the exception: a conduit or tubing length not exceeding 24 inches between boxes or enclosures may be filled to 60% per NEC Chapter 9, Table 1, Note 4. For 3" PVC Schedule 80 that raises the usable area from 2.577 in² to 3.865 in².

Other PVC Schedule 80 Sizes

3" in Other Conduit Types

Frequently Asked Questions

How many wires fit in 3-inch PVC Schedule 80 conduit?

A 3-inch PVC Schedule 80 conduit has 6.442 square inches of internal area. With more than two conductors the NEC limits fill to 40%, or 2.577 in². That works out to 193 #12 THHN, 265 #14 THHN, 122 #10 THHN, or 70 #8 THHN conductors.

How many 12 AWG THHN wires fit in 3-inch PVC Schedule 80?

193 conductors. Each 12 AWG THHN wire is 0.0133 in² per NEC Chapter 9, Table 5, and the 40% fill area of 3-inch PVC Schedule 80 is 2.577 in².

What is the maximum fill percentage for conduit?

NEC Chapter 9, Table 1 sets three limits: 53% for a single conductor, 31% for exactly two conductors, and 40% for three or more. The lower two-conductor figure exists because two round conductors pack poorly inside a round raceway.

Related

Conduit fill calculator → All conduit fill charts → Ampacity tables →